Tension Band 14ga x 3/4″ Tension bands are used to attached tension band to terminal post, with a carriage bolt. Heavy Tension Band 11ga x 1″ Heavy Tension bands are used to attached tension ban to terminal post, with a carriage bolt. Brace Band 12ga x 3/4″ Brace Band are used to attach rail end, brace rail, truss rod, tension wire, and barbed wire. Heavy Brace Band 11ga x 1″ Brace Band are used to attach rail end, brace rail, truss rod, tension wire, and barbed wire. Sign Mounting Bracket 13ga x 1″ An inexpensive bracket used to mount 2 3/8 post to commercial signs.

Dome Cap Used to keep water out of inner post. Terminal Bullet Cap Used to fasten top rail to terminal post. The concave adapter cab be fastened with a tap screw and positioned any degree. Loop Tops Loop Tops (Also called line post tops or eye tops) are used to hold top rail or tension wire above line post.

Heavy 45 degree barbed Wire Arm These arms are used to hold three strands of barbed wire at a 45 degree angle. X-Heavy 45 Degree Barbed Arms Designed to hold three strands of barbed wire at a 45 degree angle. This meets the 250 lbs down pull space. Domestic Heavy Vertical Barbed Arm Designed to hold the three strands of barbed wire vertically. Domestic Heavy V-Type Barbed Wire Designed to hold six strands of barbed wire. This arm meets the 250 lbs pull down spec. Domestic Steel Corner Barbed Arm Designed to hold three strands of terminating barbed wire on each side of the arm. Corner barbed arm is held in place with heavy set screws. Domestic Pressed Steel V-Type Copper Arm Designed to hold six strands of terminating barbed wire on each side of the “V” Arm. V-Type Corner arm is held in place with Hoy Set screws.

Hinge J-Bolt Used to mount metal panels or hinge gates of a variety of post types and sizes. Post Hinge (Male Hinge) Post hinge has a 5/8″ pin off the past hinge to swivel. Gate Hinge (Female Hinge) Gate hinge allows 5/8″ pin off the post hinge to swivel. 180 Degree Gate Hinges Pressed Steel 180 degree gate to swing 180 degree from closed to open. Show Sizes. Bull Dog Hinge Commonly used in the commercial field for its rigidity and easy installation. Allows gate to swing 90 degree from closed to open. Show Sizes. Cox Hinge  Designed to hold the heaviest gates. Allows gate to swing open up to 90 degrees from open to close. Show Sizes. Heavy Flip Latches Designed to latch gate to gate post, and allows for pad lock. Butterfly Latch Designed to automatically latch shut. Has a pad lock hole under the latch.  Fits 1 3/8 Gate Frame. Dog Kennel Latch Designed to keep dogs from pushing latch open with their nose. Spring Latch Can be to mount to 4×4 or metal post. Add Res. D Bar. & Guides. Industrial Drop Bar Latch with Guides Used to latch and lock double drive gates together. Fits gate frames that are 1 5/8 or 1 7/8. Wheel for Chain Link Swing Gate Designed to attach to gate frame inline or offset. Diameter of wheel is 6″. Fits 1 3/8, 1 5/8, or 1 7/8 Gate frame.

Gate Scrolls A decorative area that mounts to the top of a gate with self-tapping screws or can be welded on. Special Gate Clips Used to attach gate fabric to the gates frame. Fits 1 3/8″ Aluminum Gate Corners Used to join the vertical and horizontal tubing to make a gate. Fastened by bolts or self tapping screws. Fits 1 3/8″ Steel Gate Corners Designed for use in comm. gate to join the vertical and horizontal tubing to make a gate. Fastened with bolts. Fits 1 5/8 or 2″ Gate Brace Clamp A two piece clamp used to hold a center bar in a gate with a bolt. Also called a tee clamp. Sizes 1 3/8, 1 5/8 Panel Clamp Panel clamps are used to hold dog or temporary panels security. The two piece panels are help together with one 3/8″ carriage bolt and leave apprx. 1/2″ space between panels. Gate Holdback Gate holdbacks are mounted to 1 5/8 pipe and are designed to hold gate in a opened position when engaged. Also, called gatekeepers. Gate Mushroom Gate mushrooms are designed to hold drop bar and gates in place. Gate mushroom is mounted flush to the ground with a 1 5/8″ pipe. Truss Rod Designed to give lift to gates and to help keep truss on corners and ends. 3/8″x11″ Truss Rod Tightener Designed to hold truss rod in place so it can be tightened are also called assemblies.

Steel Track Roller Mounts to the frame work of the gate frame, and rolls on top of track. Fits 1 5/8 X 1 5/8 Pipe Track Bracket Brackets are designed to hold 1 5/8 track and its mounted to line post and get post with its bolts. Fits 2″ or 2 3/8″. Heavy Pipe Track Brackets More information coming soon. Universal Pipe Track Bracket Bracket is mounted to any size post using brace boards. Slide Gate Latch A two piece latch that is slide into open couples and allows for pad lock. Gate Dollys Designed to aid and support front of roll gate. Built with 6″ or 10″ rubber wheels and a 6″ or 12″ axle. 6″ Replacement Wheel Used in replacing worn wheels. Fits a 5/8″ shaft. V-Groove Wheel A 6″x2″ wheel designed to truck slide gates on an angle iron tracking system. Fits 1″x1″ angle iron. V-Groove Track V- Groove tracks are used with V-Groove wheels to help truck slide gates. 1/4″x5″ plate with 1″x1″ angle 10′ Overall.

Deluxe Cantilever Rollers Designed to hold and track 2 1/8″ cantilever gates. The deluxe rollers have 1 1/8″ axle and roll on needle bearing and greased fittings. Fits 4″x2 3/8″ Nylon Cantilever Rollers Designed for high usage gate. The nylon graphite roller allows gate to operate more smoothly. Fits 4″x2 1/8″. Cantilever Roller Guard Made to fit over cantilever roller for solety. ASTM F1184-05 requires a guard. Cantilever Gate Latch Cantilever latched are used on 2″ Gate frame, and fit a 3″ or 4″ gate post. Allows for pad lock. Fits 3″x2″ & 4.

Chain Link Stretcher Bar Used to stretch and make chain link tight. A-come-along is attached to the stretcher bar and is used to make chain link fence tight. 42″ tall. Gate Wire Stretcher Used to tighten chain link on gates to short stretches. Fits 1 3/8 to 2″ & 2 3/8 to 3″. Gate Clip Tool Used to squeeze hog rings onto fence or anything else. Makes far quick and easy installation. Hitachi Nail Gun The Hitachi NV65AH air powered coil siding nailer drives 1-1/2″ to 2-1/2″ plastic or wire collated coil siding nails.

Tension Bars Flat strips of metal that are used for attaching chain link to terminal post, with aid of tension bands. Sleeves Designed to link two joints of top rail together. Sizes 1 3/8″, 1 5/8″ Rail Ends Made to hold top rail or brace rail at terminating post. Bottom Rail Clamp Also called a mid rail clamp or bottom clamp. This two piece clamp is held together with two 5/16 carriage bolts, and is designed to hold 180 degrees horizontal rail. Straight Ties and Pig Rings Straight ties are used to fasten chain link mesh to frame work. Pig rings (also called hog rings) are typically-used to fastening chain link to bottom tension wire. EZ Twist Ties Say no more to sore hands. EZ twist ties are quicker, easier, and stronger. Contractors show a 3 to1 installation advantage. Galvanized Plate Designed for mounting post to pie-existing concrete area. Plate is welded to post. Top to floor Adapter Also called floor flange and wood rail end. Fits 2 3/8 Truss Rod Designed to hold truss rod in place so it can be tightened also called truss rod assemblies. Perlin Strap 12 gax 3/4″ two piece strap steel clamp designed to join pipe at 90 degree angles. Used mainly to construction of greenhouses.